Global Sources
EE Times-India
Stay in touch with EE Times India
EE Times-India > RF/Microwave

Multi-band wireless receivers target automotive apps

Posted: 29 Jul 2010     Print Version  Bookmark and Share

Keywords:wireless control receivers  keyless entry  short range radio  remote automotive functions 

Infineon Technologies reveals the TDA5240, TDA5235 and TDA5225 family of wireless control receivers that are suitable for use in various automotive applications, including remote keyless entry (RKE) systems, tyre pressure monitoring systems (TPMS), remote start, control, status and alarm functions. The devices provide multi-band support (315MHz, 434MHz, 868MHz and 915MHz) for ready worldwide coverage and offer the highest current available sensitivity and low power consumption.

In addition, industrial and consumer systems such as short range radio data transmission, garage door openers, cordless alarm systems, remote metering and low-power telemetry certainly would benefit from the high-integrated wireless control devices. The receivers also are capable of taking over some of the tasks that are typically performed by the system's microcontroller.

The TDA5240, TDA5235 and TDA5325 are successors to the TDA5230/31 receiver family. Two of the devices include the digital data processing capabilities of the TDA5230/31, with overall performance and feature set enhancements.

Available functionalities like IF filter (optional usage of external filter is possible) and level shifters are now integrated. Only a few external components are needed that leads to reduced BOM. An innovative integrated Low Noise Amplifier (LNA) concept provides the system developers with enhanced design alternatives. Depending on the application needs this LNA can extend the system range or even eliminate the need for an external LNA to reduce system complexity and costs.

Infineon Technologies' director for Wireless Sense and Control, Automotive Division, Matthias Halsband says, "Introduction of this new series of wireless control receivers underlines Infineon's market leadership in the RKE receiver segment." He adds that, "The new devices combine highest sensitivity and low power consumption with multi-protocol handling to increase performance and reduce system cost."

High sensitivity of the new family (typically -119dBm for FSK and typically -116dBm for ASK) is due to a reduced noise figure and noise bandwidth using improved digital signal processing. Compared to Infineon's current receiver products, which offer an average data rate of 40kchip/s, the TDA5240/35/25 devices provide a data rate with several embedded encodings and modulation schemes specified at up to 112kchip/s (FSK). System designers can use the multi-band, multi-channel receivers for systems operating at frequency bands 315/434/868/915MHz, with one crystal for all supported frequency bands well-suited for technologies worldwide.

A high-resolution sigma-delta fractional-N PLL synthesiser provides a fine multi-channel resolution of 10.5Hz. Multi-protocol handling enables flexible designs based on one platform. The receivers are capable of handling data from both RKE and TPMS transmitters, even when they have different modulation, bit rate, and data format. Therefore only one device can be used for multiple applications (RKE, TPMS, remote start, etc.) where currently there is the need for two. The wireless control receivers are based on a CMOS process providing low power consumption. The supply current is only 0.8µA in power down and 12mA in run mode.

Presence of a fast fallback to sleep function reduces the receiver's active time, when no data is available for further reduction of the average power consumption. Up to four parallel parameter sets for autonomous scanning and reception from different sources reduce significantly the host processor and system standby power consumption.

Support for additional encodings (bi-phase, NRZ) and market-leading coverage of automotive RKE/PASE/TPMS protocols results in high flexibility while minimising software development effort. The TDA5225 comes without digital base band processing to support designs based on standard concepts with data processed in the microcontroller.

Comment on "Multi-band wireless receivers target..."
*  You can enter [0] more charecters.
*Verify code:


Visit Asia Webinars to learn about the latest in technology and get practical design tips.


Go to top             Connect on Facebook      Follow us on Twitter      Follow us on Orkut

Back to Top